Metering Supply Mains Energy Power(Mounted) - ElectroSource
Mains metering monitoring and control(Mounted)

Mains metering monitoring and control(Mounted)

Energy (kWh meters)
Energy (kWh meters)
Load control(load shedding)
Load control(load shedding)
Mains Ammeters
Mains Ammeters
Mains Frequency meters
Mains Frequency meters
Mains metering accessories
Mains metering accessories
Max Demand meters
Max Demand meters
Multimeters / Analysers
Multimeters / Analysers
Power factor meters -Controllers, Capacitors
Power factor meters -Controllers, Capacitors
Voltmeter
Voltmeter
Mains metering monitoring and control(Mounted)

Mains metering monitoring and control(Mounted)

Product Attributes
                                                                                                   
Number of attributes100
Show: 
gary test1
 Image   Products+   Manufacturer 
Ammeter,LA5/5P - 5Amp current monitor  Ammeter,LA5/5P - 5Amp current monitor

LA5/P:- 1-5Amp UNDER CURRENT, 1phase AC current monitor. Adjustable setpoint and reponse delay.Reset button, 11pin plug in relay, 1x SPDT relay. One 5amp CT for input. Preset 5% hysteresis. *During timing period the power LED flashes. 10 sec power up delay - Does not monitor fault for first 10 seconds after power up. Adjustable 0.5 - 30minutes response delay. Under current:- Current lower then the setpoint will de-energise relay. The relay will only energise again if the voltage has risen by the hysteresis amount. Button reset on faceplate or cycle power.

 
 ElectroDev 
CX01 Opto-programming cable  CX01 Opto-programming cable

Programming cable for all Lovato products with the front connecting infrared port.

 
 Lovato 
CX02 - Wifi device  CX02 - Wifi device

Wi-Fi connecting device for programming

 
 Lovato 
EXM1000 - 2 Inputs + 2 SSR - Expansion module   EXM1000 - 2 Inputs + 2 SSR - Expansion module 

Isolated digital inputs(sink/NPN-source/PNP) and 2 optomosfet-isolated protected static outputs(40Vdc/30Vac/55mA). LED inication for power, Optic-Connectivity, I/O status. Built in 24Vdc/1W/42mA power supply.

 
 Lovato 
EXM1001 - 2 Inputs + 2 relays - Expansion module   EXM1001 - 2 Inputs + 2 relays - Expansion module 

Isolated digital inputs (sink/NPN-source/PNP), Output relays 1C/Over, 250V/5A. Built in 24Vdc/1W/42mA power supply.

 
 Lovato 
EXM1010 - USB port. expansion module   EXM1010 - USB port. expansion module     
EXM1011 - RS232 Comms Expansion module   EXM1011 - RS232 Comms Expansion module 

RJ11 6/6, Comms rate: 1200 38400 bps

 
 Lovato 
EXM1012 - RS485 Comms Expansion module   EXM1012 - RS485 Comms Expansion module 

Comms rate: 1200 38400 BPS 

 
 Lovato 
EXM1013 Ethernet expansion module   EXM1013 Ethernet expansion module 

RJ45 connector, Led indication for Power on, Infrared connection ok, communicating.  Protocols:RJ45 Ethernet 10BASE-T or 100BASE-TX (auto-sensing)Ethernet: Versione 2.0/IEEE802.3:  ARP, UDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, Auto IP, e HTTP

 
 Lovato 
EXM1020 - RS485 + 2 output relays - Expansion module   EXM1020 - RS485 + 2 output relays - Expansion module 

RS485 comms port, Output relays 1C/Over, 250V/5A. Built in 24Vdc/1W/42mA power supply. Modbus RTU and Modbus ASCII

 
 Lovato 
EXM1030 - RTC, Datalogger  EXM1030 - RTC, Datalogger

Data storage, RTC with backup reserve energy for data logging. Capacitor backup for up to 2 weeks.

 
 Lovato 
EXP 10 00  - 4Digital inputs  EXP 10 00 - 4Digital inputs

EXP1000 - 4 isolated digital inputs. Sink/ NPN, source/PNP, PUSH PULL and active sensors (e.g.: 3 wire inductive proximity sensors). Builtin 24Vdc/1W/42mA power supply

 
 Lovato 
EXP 10 01  - 4 SSR electronic outputs  EXP 10 01 - 4 SSR electronic outputs

4 x independant isolated solid state relay optomosfets (SSR) outputs Bidirectional SSR, 40Vdc / 30Vac / 55mA.

 
 Lovato 
EXP 10 01 - 2 Inputs + 2 RELAYS  EXP 10 01 - 2 Inputs + 2 RELAYS

2 x Isolated digital inputs (sink/NPN-source/PNP), 2 x relays -1C/Over each, 250V/5A, Built in 24Vdc/1W/42mA power supply.

 
 Lovato 
EXP 10 02 - 2inputs, 2 SSR outputs  EXP 10 02 - 2inputs, 2 SSR outputs

2 isolated digital input contact, sink/NPN and source/PNP open collector and active sensors with digital output (e.g.: 3 wire proximity sensors). 2 isolated OPTO-MOSFET independant protected 40Vdc / 30Vac / 55mA. electronic outputs. Builtin 24Vdc/1W/42mA power supply

 
 Lovato 
EXP 10 03 - 2 output relays  EXP 10 03 - 2 output relays

1 x Changeover contact per relay. • 250Vac/5A relays.

 
 Lovato 
EXP 10 05 - 2 x Analogue outputs  EXP 10 05 - 2 x Analogue outputs

Multifunction outputs: 0 to 10V or ±5V range or 0/4 to 20mA

 
 Lovato 
EXP 10 13 - ETHERNET expansion module  EXP 10 13 - ETHERNET expansion module

RJ45 connector, Led indication for Power on, Infrared connection ok, communicating. Protocols:RJ45 Ethernet 10BASE-T or 100BASE-TX (auto-sensing)Ethernet: Versione 2.0/IEEE802.3: ARP, UDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, Auto IP, e HTTP

 
 Lovato 
EXP10 04 - 2 analogue inputs  EXP10 04 - 2 analogue inputs

2 x Multifunction inputs: 0 to 10V or ±5V range; 0/4 to 20mA; 2 wire PT100 sensor(-50°C÷250°C).

 
 Lovato 
EXP10 10 USB port  EXP10 10 USB port

EXP10 10 USB port

 
 Lovato